Zinc Oxide Desulfurizer Catalyst

Zinc Oxide Desulfurizer Catalyst: *Desulfurization catalyst *Zinc oxide catalyst *High sulfur capacity *Low pressure drop

Zinc Oxide Desulfurizer Catalyst

HL-306 is applicable to desulfurization of residue cracking gases or syngas and purification of feed gases for

organic synthesis processes. It is suitable for both higher (350--408°C) and lower(150--210°c) temperature use.

It can convert some simpler organic sulfur while absorbing inorganic sulfur in gas stream. Main reaction of the

desulfurization process is as follows:

(1) Reaction of zinc oxide with hydrogen sulfide H2S+ZnO=ZnS+H2O

(2) Reaction of zinc oxide with some simpler sulfur compounds in two possible ways.

2.Physical Properties

Appearance	white or light-yellow extrudates
Particle size , mm	Φ4×4--15
Bulk density, kg/L	1.0-1.3

3.Quality Standard

crushing strength, N/cm	≥50
loss on attrition, %	≤6
Breakthrough sulfur capacity, wt%	≥28(350°C)≥15(220°C)≥10(200°C)

4. Normal Operation Condition

Feedstock : synthesis gas , oil field gas, natural gas, coal gas. It can treat gas stream with inorganic sulfur as high

as 23g/m3 with satisfactory purification degree. It can also purify gas stream with up to 20mg/m3 of such simpler

organic sulfur as COS to less than 0.1ppm.

5.Loading

Loading depth: Higher L/D (min3) is recommended. Configuration of two reactors in series can improve utilization

efficiency of the adsorbent.

Loading procedure:

(1)Clean the reactor before loading;

(2)Put two stainless grids with smaller mesh size than the adsorbent;

(3)Load a 100mm layer of Φ10—20mm refractory spheres upon the stainless grids;

(4)Screen the adsorbent to remove dust;

(5)Use special tool to ensure evenly distribution of the adsorbent in the bed;

(6)Inspect uniformity of the bed during loading. When inside-reactor operation is needed, A wood plate should be put on the adsorbent for the operator to stand upon.

(7)Install A stainless grid with small mesh size than the adsorbent and a 100mm layer of Φ20—30mm refractory spheres at the top of the adsorbent bed so as to prevent entrainment of the adsorbent and ensure

even distribution of the gas stream.

6.Start-up

(1)Replace the system by nitrogen or other inert gases until oxygen concentration in the gas is less than 0.5%;

(2)Preheat the feed stream with nitrogen or feed gas under ambient or elevated pressure;

(3)Heating speed: 50°C/h from room temperature to 150°C (with nitrogen) ; 150°C for 2 h (when heating medium is

shifted to feed gas ), 30°C/h over 150°C until required temperature is attained.

(4)Adjust the pressure steadily until the operation pressure is attained.

(5)After pre-heating and pressure elevation,the system should first be operated at half load for 8h. Then raise the

load steadily when operation becomes stable till full-scale operation.

7.Shut-down

(1)Emergent shut-down gas (oil) supply.

Close inlet and outlet valves. Keep the temperature and pressure.If necessary ,use nitrogen or hydrogen-nitrogen

gas to maintain the pressure to prevent negative pressure.

(2) Change-over of desulfurization adsorbent

Close inlet and outlet valves. Steadily lower the temperature and pressure to ambient condition. Then isolate the

desulfurization reactor from the production system. Replace the reactor with air until oxygen concentration of >20% is attained. Open the reactor and unload the adsorbent.

(3) Equipment maintenance (overhaul)

Observe the same procedure as shown above except that pressure should be loweredat 0.5MPa/10min and temp.

lowered naturally.

The unloaded adsorbent shall be stored in separate layers. Analyze the samples taken from each layer to determine

status and service life of the adsorbent.

8.Transportation and storage

(1)The adsorbent product is packed in plastic or iron barrels with plastic lining to prevent moisture and chemical

contamination.

(2)Tumbling, collision and violent vibration should be avoided during transportation to prevent pulverization of the

adsorbent.

(3)The adsorbent product should be prevented from contact with chemicals during transportation and storage.

(4)The product can be stored for 3-5 years without deterioration of its properties if appropriately sealed.

Zinc Oxide Desulfurizer Catalyst